/*
 * teasense.ino - Arduino code for the tea sensor
 * Copyright (C) 2023 William Moore
 *
 * This program is free software: you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the Free
 * Software Foundation, either version 3 of the License, or (at your option)
 * any later version.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of  MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along with
 * this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
 // Coded for the Arduino Uno WiFi rev. 2
// Uses a standard PT100 RTD and the Adafruit MAX 31865 interface.

#include <SPI.h>
#include <WiFiNINA.h>
#include <Adafruit_MAX31865.h>

// Create a file called config.h that contains the following:
// char ssid[] = "SSID";
// char pass[] = "Password";

#include "config.h"

// Use software SPI: CS, DI, DO, CLK
Adafruit_MAX31865 thermo = Adafruit_MAX31865(10, 11, 12, 13);
#define RREF 430.0
// The 'nominal' 0-degrees-C resistance of the sensor
// 100.0 for PT100, 1000.0 for PT1000
#define RNOMINAL 100.0

int status = WL_IDLE_STATUS;  //connection status
const int port = 80;
WiFiServer server(port);

void setup() {
  Serial.begin(9600);

  thermo.begin(MAX31865_3WIRE);  // set to 2WIRE or 4WIRE as necessary

  Serial.println("Welcome to teasense!");

  String fv = WiFi.firmwareVersion();
  if (fv < WIFI_FIRMWARE_LATEST_VERSION) {
    Serial.println("Please upgrade the firmware");
  }

  // attempt to connect to WiFi network:
  while (status != WL_CONNECTED) {
    Serial.print("Attempting to connect to SSID: ");
    Serial.println(ssid);
    // Connect to WPA/WPA2 network. Change this line if using open or WEP network:
    WiFi.setHostname("teasensor");
    status = WiFi.begin(ssid, pass);

    // wait 10 seconds for connection:
    delay(10000);
  }
  server.begin();
  // you're connected now, so print out the status:
  printWifiStatus();
  
}

void printWifiStatus() {
  // print the SSID of the network you're attached to:
  Serial.print("SSID: ");
  Serial.println(WiFi.SSID());

  // print your board's IP address:
  IPAddress ip = WiFi.localIP();
  Serial.print("IP Address: ");
  Serial.println(ip);

  IPAddress gw = WiFi.gatewayIP();
  Serial.print("Gateway IP: ");
  Serial.println(gw);

  // print the received signal strength:
  long rssi = WiFi.RSSI();
  Serial.print("signal strength (RSSI):");
  Serial.print(rssi);
  Serial.println(" dBm");
}

void enable_WiFi() {

  String fv = WiFi.firmwareVersion();
  if (fv < "1.0.0") {
    Serial.println("Please upgrade the firmware");
  }
  Serial.println(fv);
}

void connect_WiFi() {
  // attempt to connect to Wifi network:

  // while (status != WL_CONNECTED) {
    Serial.print("Attempting to connect to SSID: ");
    Serial.println(ssid);
    // Connect to WPA/WPA2 network. Change this line if using open or WEP network:
    WiFi.disconnect();
    
    status = WiFi.begin(ssid, pass);
    // wait 10 seconds for connection:
    delay(5000);
  // }
}

int resetCounter = 0;

void loop() {
  WiFiClient client = server.available();
  if (client) {
    Serial.println("new client");  // print a message out the serial port
    String currentLine = "";       // make a String to hold incoming data from the client
    if (client.connected()) {
      Serial.println("Reading data from sensor");
      String postData = "{\"temperature\": ";
      postData += thermo.temperature(RNOMINAL, RREF);
      postData += "}";
      // Serial.println(postData);
      String httpResponse = "HTTP/1.1 200 OK\r\n";
      httpResponse += "Content-type: application/json\r\n";
      httpResponse += "Connection: close\r\n\r\n";
      httpResponse += postData;
      client.print(httpResponse);
      Serial.println("HTTP Data Written");
    }
    delay(1);
    Serial.println("Data written");
    client.stop();
  }
}